Professional service HP

HP Error 59.F0

What the code means · Diagnosis at a glance

HP error 59.F0 (shown in full as 59.00.F0) appears as the printer starts up and it cannot print. HP documents two causes: the image transfer belt (ITB) is stuck and cannot rotate, or Sensor SR17 (the primary transfer-roller-disengagement sensor) is bad. It is a hardware fault in the transfer section, sometimes called a "transfer alienation failure". The only user step is to power the printer off and back on; if the error persists, HP directs you to an authorised service provider, because the transfer belt and its sensor are internal parts that are not a safe home repair.

Jump to the fix ↓ HP: 59.00.F0 Error ↗
Disconnect power firstA full power cycle is the only safe user step: switch off, wait, switch on.
May need a technicianIf 59.F0 returns, the transfer belt or SR17 sensor needs HP-authorised service.
Do not open internal partsDo not open or disassemble the transfer section; it is not a home repair.
Model-specificThis is a laser transfer-unit error; it appears on LaserJet / Color LaserJet models with an ITB, not on home inkjets.

Affected brands & models

HP LaserJet / Color LaserJet models with an image transfer belt (ITB)Enterprise and workgroup laser printersNot seen on home inkjets: this is a laser transfer-unit error

Diagnosis at a glance

Likely causes ranked, with severity and the recommended action.

Image transfer belt (ITB) is stuck and cannot rotate Service Likelihood: Most likelyAction: Power-cycle; if it returns, HP service to inspect the ITB
Sensor SR17 (primary transfer-roller-disengagement) is faulty Service Likelihood: CommonAction: HP service to test or replace the sensor
A transient glitch on start-up Quick fix Likelihood: OccasionalAction: Turn the printer off, wait, and on again

What the code means

HP error 59.F0 (written in full as 59.00.F0) is reported the moment the printer boots, and it stops the printer from printing. HP attributes it to one of two conditions in the transfer section: the image transfer belt (ITB), which carries toner from the drums toward the paper, is stuck and cannot rotate; or Sensor SR17, the primary transfer-roller-disengagement sensor, has failed. The mechanism that engages and disengages the transfer roller is what the 59.xx family of codes watches, and 59.F0 specifically flags this disengagement stage.

Because the fault sits inside the transfer assembly, there is no consumable to swap or setting to change from the panel. The one thing worth trying is a full power cycle, which clears a transient start-up glitch. If the code comes straight back, the belt or its sensor needs to be inspected by a technician. These are internal, high-precision parts, and forcing the mechanism by hand can cause further damage.

Most frequent causes

  • The image transfer belt (ITB) is jammed or seized and cannot turn.
  • Sensor SR17, which detects transfer-roller disengagement, is faulty.
  • The transfer-roller engage/disengage mechanism is sticking.
  • A one-off error during the start-up sequence (cleared by a power cycle).

Quick fix: try this first

  1. Turn the printer off, wait about a minute, and turn it back on.
  2. If the error clears, print a short test job to confirm.
  3. If 59.F0 returns immediately, stop and arrange HP-authorised service.

Step-by-step solution

0 / 4 done

Tick each step as you go. Your progress is kept while you work.

Before you start

  • Have the printer model and serial number ready for HP support.
  • Note whether the error appears every time at start-up or only occasionally.
  • If the printer is under warranty or a service contract, check that before any repair.

What not to do

  • ×Do not try to free the transfer belt by turning it by hand. It is a precision part.
  • ×Do not keep power-cycling repeatedly if the error returns every time; that will not fix a hardware fault.
  • ×Do not open or remove the transfer assembly yourself unless you are a trained technician.

When to stop & call support

If 59.F0 comes back immediately after a power cycle, stop. The image transfer belt or the SR17 disengagement sensor is at fault, and both are internal parts that HP directs to an authorised service provider. Continuing to run or force the printer risks further damage to the transfer section.

If the error comes back

If the error clears after a power cycle but returns over the following days, treat it as an intermittent transfer-unit fault rather than a fluke. Note how often it happens and arrange service. An ITB or sensor that is beginning to fail will usually get worse, and catching it early keeps the repair contained to the transfer unit.

Related parts & consumables

Image transfer belt (ITB)Moves toner toward the paper; inspected or replaced at HP service if seized
Sensor SR17Primary transfer-roller-disengagement sensor; tested or replaced by a technician

Questions about HP 59.F0

What does 59.F0 mean on an HP printer?

It is a transfer-unit fault: HP says the image transfer belt is stuck and cannot rotate, or Sensor SR17 (transfer-roller-disengagement) is bad. It appears at start-up and stops printing.

Can I fix 59.F0 myself?

The only user step HP lists is turning the printer off and on. If the error returns, it needs an authorised technician: the belt and sensor are internal parts, not a safe home repair.

Is 59.F0 the same as 59.00.F0?

Yes. 59.00.F0 is the full form of the code and 59.F0 is the short form shown on many panels; both refer to the same transfer-disengagement fault.

PrinterErrors editorial team

Last updated · Content is independent and not sponsored by any manufacturer.

Sources & methodology

Spotted something inaccurate? Report a content issue

Related error codes

50.2 Fuser error (another LaserJet hardware stop)

Related problems

Printer not printing
See all error codes HP ›